LEDFUL LED DISPLAY: Fine Pitch Rental Event Commercial Advertising Sports Perimeter

Rental Event Small LED Display SI2.9 | SI3.9 | SI4.8 SO3.9 | SO4.8 | SO5.9 Front Maintenance Curved Installation No Light Leakage Light and Thin Parameter S Series Outdoor SO 3.9 SO 4.8 SO 5.9 Pixel Pitch(mm) 3.91mm 4.81mm 5.95mm Pixel Matrix Per Sq.m 65536 43264 28224 Pixel Configuration SMD1921 SMD2727/1921 SMD2727 Brightness (nits) ≥6500 ≥5500 ≥6500 Scan 43108 43113 43107 Cabinet Resolution 128×128 104×104 84×84 Power Con. (Max / Avg) 790/ 250 w/sq.m 720 / 220 w/sq.m 650/ 220 w/sq.m Refresh Rate (HZ) 3840 3840 1920 Cabinet Weight 8kg / 17.6Ib Module Dimension 250x250mm / 0.82x0.82feet Cabinet Dimension 500x500x85mm / 1.64x1.64x0.28feet Cabinet Material Die-casting Aluminum Service Access Front / Rear Grey Scale (bit) 14 Viewing Angle (H/V) 140 / 140 IP Rate IP65 Input Voltage (AC) 110 / 240   S Series Indoor SI 2.9 SI 3.9 SI 4.8 Pixel Pitch(mm) 2.976mm 3.91mm 4.81mm Pixel Matrix Per Sq.m 112896 65536 43264 Pixel Configuration SMD1515 SMD2121 SMD2121 Scan 43128 43116 43113 Cabinet

Hello, how can we install sending card led to our led display? It is quite normal that the clients would choose to use their own PC, as the controller of led display card . In this case, you would need to assemble the sending card and graphics card to your PC. Here we will show you the process. Before starting, please get on hand the parts as below: Please power off the PC and follow the steps as below: 1.Connect the DVI Graphic Card (we provide) to the PCI-E (or AGP) of the computer motherboard (mainboard, system board). Then connect the DVI Graphic Card to the PC monitor, via the VGA port. 2.Connect the Sending Card to the PCI of the computer motherboard (mainboard, system board). 3.Connect the DVI Graphic Card to the Sending Card, by the DVI cable provided. 4.Connect the Sending Card to the USB port of the computer. 5.Connect the signal cable to the Sending Card (either one of the RJ45 ports). 6.Turn on the PC, and check the indicator light of sending card. (Red on, Green

LED Screen Maintenance 1. Keep the damp or other humid things out of the outdoor LED Screen. Power on the commercial led display screen with humidity that will cause the components corrosion, then the perpetual damage. 2. Do a good cleaning for the outdoor LED Screen. After a long-time use, there must be lots of dust cover the screen that will impact the viewing effect and also is bad for the electric circuit. So wipe out the dust timely, do it lightly to reduce the harm to the minimum. 3. No water or electric conduction things in Outdoor LED Display screen. Please cut off the power immediately if water is found in the screen or cabinet. Only re-start the LED Display after make sure the inner screen panel is dry. 4. Ensure the stable power supply voltage and good ground protection. It’s recommended do not use the outdoor LED Screen in bad weather like strong thunder and lightning days. 5. Switching sequence: Start the control computer first, after it works normally, power on the

LED Display Screen Price : Led display supplier: Many clients like asking what's your best price. Every Led display supplier will have their own price and the difference is big. It all depends on the material they use. Once the client asks cheaper prices they have to buy a bigger pitch, once that is not an option the led display supplier might use low-quality material that might affect the product in a few months or after a few years depends on how low they can go. Which means service and quality are both very important. Indoor and Outdoor Price: Outdoor is always more expensive than indoor for the same kind of display. This is also very normal since outdoor led displays have high requirements for the waterproof, so it needs more material and time to make it. Pitch Price: Everyone in the outdoor led display advertising world will talk about the Led pitch. At the moment the led pitch for indoor and outdoor are getting smaller and smaller. And sure the smaller the pitch means hig

Nowadays, light pollution is everywhere in our lives in the city. Especially, with many LED screen setup on shopping mall, bank, commercial area, plaza, etc where near people residence, too high brightness of LED screen often influence people's rest and sleep. Therefore, led screen owner or building owner received any complaint, even receive a warning from a lawyer.So it is very important and necessary to make the corresponding solution. We need to make LED screen brightness automatically, not only changeless bright in the nighttime, but also protect audience eyes in the daytime. We introduced multi-function card hardware function and connection in last pages, now we introduce how to setup led screen auto brightness in LED screen software. 1)Option -- software setup 2)Input"linsn", psd"168" 3)tick "enable excard bright" 4)Option -- led screen monitor 5)Check data for brightness, temperature, humidity. If you are not clear on multi-function card h

Baixar LED studio is software from Linsn control system for LED display. Because Linsn system multi-function and easy operation, it is adopted in most LED display. Here we introduce clients FAQ. Question: What's led studio serial number and password of led studio? Answer: LED studio serial number is 888888, password is: after input "linsn", then "168". Question: How to load RCG file and CON file? Answer: Pls check below steps: If you want to know more details of ledstudio12 and led studio 12.61, please visit our website. Now the price of street advertising screens is reasonable, if you have needs, please contact us.